Quoted from my manual If you select Manual, related information is asked to be entered to the following items. When I search with: A single floppy drive needs to be plugged into the end connector on the other end of the data cable, not the middle connector on a 3 connector data cable. For and XP, 80gb, or smaller, may be fine, minimum, say, 20gb, if you’re not greedy about what you download to or have on your computer. People often assume they’re only formatting a drive in and up when they make a new partition because only the initial messages you see are about software partitioning [NTFS, FAT32, or FAT if the partition is 2.

Uploader: Arashilkree
Date Added: 14 October 2004
File Size: 14.26 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 50403
Price: Free* [*Free Regsitration Required]

If you copy the entire contents of the partition Windows is installed on, that can only be used with the same mboard or an identical one, or for a mboard that is very similar.

Help me resurrect a throw-away MS VER:1

In really old bioses, msii as the Award 4. I would like to point out that there are very people who reply to our those of us who frequently answer posts in as much detail as you have – we appreciate that. In older bioses it’s size and parameters cylinders, heads, etc.

I got the same message: If the XP CD does not have the drivers for the network adapter, you will not see that near the end of Setup. If you don’t have one, someone you know might have one. I wondered whether or not, if the floppy drive was functional and had only the power connector connected to it, the LED would come on, without the data cable connected – I did not know that the LED was a function of one of the BIOS settings.

The pin 1 end is usually marked on the mboard surface near the mboard IDE header with an arrowhead or a 1; the pin 1 end of an IDE hard drive or optical drive connector is usually next to the drive’s power connector. Usually there is a 5 second delay while booting during which you can press the key. The Seagate SeaTools will test any brand of hard drive, but if it does find LBA errors in the long ,si, it’s recommended you then run the diagnostics program that the hard drive manufacturer provides on their own web site to try to repair the problem by writing zeros mso the drive – you often cannot choose to do that until you have run whatever long test those diagnostics provide.


20 Most Recent MSI GEM-L (MS) Motherboard Questions & Answers – Fixya

Must I take it out and put it on the other pins? Only insert on stick to start. You should do this anyway.

A moment of silence for my 6. If you want to do that over the internet, you need to install the drivers for the network adapter that’s built into the first.

A single floppy drive needs to be plugged into the end connector on the other end of the data cable, not the middle connector on a 3 connector data cable. These are primarily portable versions of Linux. For Win ME or below, a smaller drive than that is fine – minimumsay, 10gb.

MSI MS-6714 Manuals

Whether or not a data cable connection has a problem at the same time should usually have no effect on whether the led comes on, but in theory it’s possible it may not come on if there is a short between wires in the data cable extremely unlikelyor if the connector was not on all the pins. If you don’t enter one that is acceptable to Setup, you can’t continue to install Windows.

Must I reconnect it to the computer now without the jumper? The OS on the disk must be unpacked and installed, along with the proper drivers to support your hardware configuration. Please read 51 above.

Our 614 problem is probably that those who start a subject usually don’t provide enough information or feedback to our responses, I suspect often because they’re just too lazy to do so. If the VGA port is attached directly to the motherboard you have integrated.

If you have both a video port for onboard video, and a video port on a card in a slot space, you must plug the monitor into the video port on the card in a slot space – most mboards will produce no video mmsi the onboard video port when a video card is installed in an AGP or PCI-E X16 card slot.


If you set the boot order to CD first and you see the failure message then you don’t have a bootable CD inserted, or possibly you didn’t hit any key to boot from the CD drive when prompted.

I msj them all over but found nothing that quite fit my situation. The only time I can remember a long beep like you describe, it started not right away while booting but within a few seconds, it was caused by the ram not being seated properly, and the same mboard 66714 not do that when no ram was installed.

Mi the end of Setup, if XP has installed drivers for your network adapter, you will be asked if you want to Activate Windows. When you find what seems to be the right one, click on the link for the manual.

MSI MS 6714 Ver 5, Socket 478, Intel Motherboard

I learned from you that a hard drive is not required to order for the computer to POST Power On Self Testso it made sense to me to verify mzi the existing hardware is good before considering getting a hard drive. For the time being, you could just install it and see how mxi goes with Adobe CS4.

It’s up to whoever made the specific bios version what they want the user to see in the bios Setup screens. You can either do that then, over the internet, or by phoning a number that connects you to an automated answering machine, or you can do that after Setup has mis, by selecting to Activate Windows in your All Programs list. Required components cpu and heatsink, ram.